要するに:
chmod +x
ファイル(スクリプト)でのみ、実行可能にすることを意味します。右のスクリプトをクリックし、選択したプロパティ ] - > [ 権限 ] - > [ プログラムとファイルの実行を許可すると、端末内のコマンドとまったく同じ結果に葉君を。
パーミッションを変更したいファイルがシステムディレクトリ内にある場合root
、次のようにする必要があるかもしれません:(sudo
コマンドの使用中は注意してください)
sudo chmod +x /usr/share/testfolder/aFile
また、ここでアーカイブしたい内容が明確ではありません。質問を編集して、実際の問題に関する詳細を入力してください!
詳細については、この質問を参照することもできます。chmodu + x '対' chmod + x
長い:
入力man chmod
ターミナルウィンドウで(Ctrl+ Alt+ T)、あなたは次のような出力が得られます。
NAME: chmod-ファイルモードビットの変更
あらすじ
chmod [OPTION]... MODE[,MODE]... FILE...
chmod [OPTION]... OCTAL-MODE FILE...
chmod [OPTION]... --reference=RFILE FILE...
記述
This manual page documents the GNU version of chmod. chmod changes the
file mode bits of each given file according to mode, which can be either
a symbolic representation of changes to make, or an octal number repre‐
senting the bit pattern for the new mode bits.
The format of a symbolic mode is [ugoa...][[+-=][perms...]...], where
perms is either zero or more letters from the set rwxXst, or a single
letter from the set ugo. Multiple symbolic modes can be given, sepa‐
rated by commas.
A combination of the letters ugoa controls which users' access to the
file will be changed: the user who owns it (u), other users in the
file's group (g), other users not in the file's group (o), or all users
(a). If none of these are given, the effect is as if a were given, but
bits that are set in the umask are not affected.
The operator + causes the selected file mode bits to be added to the
existing file mode bits of each file; - causes them to be removed; and =
causes them to be added and causes unmentioned bits to be removed except
that a directory's unmentioned set user and group ID bits are not
affected.
The letters rwxXst select file mode bits for the affected users: read
(r), write (w), execute (or search for directories) (x), execute/search
only if the file is a directory or already has execute permission for
some user (X), set user or group ID on execution (s), restricted dele‐
tion flag or sticky bit (t). Instead of one or more of these letters,
you can specify exactly one of the letters ugo: the permissions granted
to the user who owns the file (u), the permissions granted to other
users who are members of the file's group (g), and the permissions
granted to users that are in neither of the two preceding categories
(o).
A numeric mode is from one to four octal digits (0-7), derived by adding
up the bits with values 4, 2, and 1. Omitted digits are assumed to be
leading zeros. The first digit selects the set user ID (4) and set
group ID (2) and restricted deletion or sticky (1) attributes. The sec‐
ond digit selects permissions for the user who owns the file: read (4),
write (2), and execute (1); the third selects permissions for other
users in the file's group, with the same values; and the fourth for
other users not in the file's group, with the same values.
chmod never changes the permissions of symbolic links; the chmod system
call cannot change their permissions. This is not a problem since the
permissions of symbolic links are never used. However, for each sym‐
bolic link listed on the command line, chmod changes the permissions of
the pointed-to file. In contrast, chmod ignores symbolic links encoun‐
tered during recursive directory traversals.
SETUIDおよびSETGIDビット
chmod clears the set-group-ID bit of a regular file if the file's group
ID does not match the user's effective group ID or one of the user's
supplementary group IDs, unless the user has appropriate privileges.
Additional restrictions may cause the set-user-ID and set-group-ID bits
of MODE or RFILE to be ignored. This behavior depends on the policy and
functionality of the underlying chmod system call. When in doubt, check
the underlying system behavior.
オプション
Change the mode of each FILE to MODE.
-c, --changes
like verbose but report only when a change is made
--no-preserve-root
do not treat `/' specially (the default)
--preserve-root
fail to operate recursively on `/'
-f, --silent, --quiet
suppress most error messages
-v, --verbose
output a diagnostic for every file processed
--reference=RFILE
use RFILE's mode instead of MODE values
-R, --recursive
change files and directories recursively
--help display this help and exit
--version
output version information and exit
Each MODE is of the form `[ugoa]*([-+=]([rwxXst]*|[ugo]))+'.