Ubuntuでkismet.confを設定する方法

apt-get install kismetとして私のUbuntu 10.04マシンにKismetをインストールしました。 すべてがうまくいっているようです。

しかし、起動すると以下のエラーが表示されます。

キスメット

Launching kismet_server: //usr/bin/kismet_server
Suid priv-dropping disabled.  This may not be secure.
No specific sources given to be enabled, all will be enabled.
Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng)
Enabling channel hopping.
Enabling channel splitting.
NOTICE: Disabling channel hopping, no enabled sources are able to
change channel.
Source 0 (addme): Opening none source interface none...
FATAL: Please configure at least one packet source.  Kismet will not
function if no packet sources are defined in kismet.conf or on the
command line.  Please read the README for more information about
configuring Kismet.
Kismet exiting.
Done.

私はこのガイドに従った http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776

kismet.confの中で私は次の行ではっきりしない

source=none,none,addme

これを何に変更すればよいですか。

lspci -vnn番組

0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01)
    Subsystem: Dell Device [1028:000c]
    Flags: bus master, fast devsel, latency 0, IRQ 17
    Memory at f69fc000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [40] Power Management version 3
    Capabilities: [58] Vendor Specific Information <?>
    Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
    Capabilities: [d0] Express Endpoint, MSI 00
    Capabilities: [100] Advanced Error Reporting <?>
    Capabilities: [13c] Virtual Channel <?>
    Capabilities: [160] Device Serial Number 
    Capabilities: [16c] Power Budgeting <?>
    Kernel driver in use: wl
    Kernel modules: wl, ssb

そして

iwconfigが示す

lo        no wireless extensions.

eth0      no wireless extensions.

eth1      IEEE 802.11bg  ESSID:"WIKUCD"  
          Mode:Managed  Frequency:2.462 GHz  Access Point: <00:43:92:21:H5:09>
          Bit Rate=11 Mb/s   Tx-Power:24 dBm   
          Retry min limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Managementmode:All packets received
          Link Quality=1/5  Signal level=-81 dBm  Noise level=-90 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:169  Invalid misc:0   Missed beacon:0

だから私は代わりに何を置くべきです

 source=none,none,addme

私は上記の出力で？

から Kismet Readme

WL（Linux、Intel）

  Broadcom has released a binary version of their drivers called WL.
  These drivers are incapable of monitor mode, and cannot be used with
  Kismet.  Kismet will attempt to autodetect them and report this to the 
  user.  Users of Broadcom cards should use the b43 or b43xx in-kernel
  drivers.

だから試してみてください

source=bcm4312,none,kbr0

私はそれがうまくいくと思います。